Part 4 (2/2)
The chapter on House Building will give more detailed ill.u.s.trations of large structures, and how they are framed and braced. At this point we are more concerned in knowing how to proceed in order to lay out the simple structural details, and if one subject of this kind is fully mastered the complicated character of the article will not be difficult to master.
OBSERVATIONS ABOUT A BOX.--As simple a little article as a box frequently becomes a burden to a beginner. Try it. Simply keep in mind one thing; each box has six sides. Now, suppose you want a box with six equal sides--that is, a cubical form--it is necessary to make only three pairs of sides; two for the ends, two for the sides and two for the top and bottom. Each set has dimensions different from the other sets. Both pieces of the set, representing the ends, are square; the side pieces are of the same width as the end pieces, and slightly longer; and the top and bottom are longer and wider than the end pieces.
[Ill.u.s.tration: _Fig. 41._]
A box equal in all its dimensions may be made out of six boards, properly cut. Make an attempt in order to see if you can get the right dimensions.
JOINTS.--For joining together boards at right angles to each other, such as box corners, drawers and like articles, tenons and mortises should never be resorted to. In order to make fine work the joints should be made by means of dovetails, rabbets or rebates, or by beveling or mitering the ends.
BEVELING AND MITERING.--There is a difference in the terms ”beveling”
and ”mitering,” as used in the art. In Fig. 42 the joint A is _beveled_, and in Fig. 43 the joint B is _mitered_, the difference being that a bevel is applied to an angle joint like a box corner, while a miter has reference to a joint such as is ill.u.s.trated in Fig. 43, such as the corner of a picture frame.
[Ill.u.s.tration: _Fig. 42._]
[Ill.u.s.tration: _Fig. 43._]
PROPER TERMS.--It is the application of the correct terms to things that lays the foundation for accurate thinking and proper expressions in describing work. A wise man once said that the basis of true science consists in correct definitions.
PICTURE FRAMES.--In picture frames the mitered corners may have a saw kerf (C) cut across the corners, as shown in Fig. 44, and a thin blade of hard wood driven in, the whole being glued together.
DOVETAIL JOINTS.--It is in the laying out of the more complicated dovetail joints that the highest skill is required, because exactness is of more importance in this work than in any other article in joinery. In order to do this work accurately follow out the examples given, and you will soon be able to make a beautiful dovetail corner, and do it quickly.
[Ill.u.s.tration: _Fig. 44._]
PREPARING A BOX JOINT.--In order to match a box joint for the inner end of a table drawer, the first step is to select two work sides. One work side will be the edge of the board, and the other the side surface of the board, and on those surfaces we will put crosses, as heretofore suggested.
[Ill.u.s.tration: _Fig. 45._]
[Ill.u.s.tration: _Fig. 46._]
[Ill.u.s.tration: _Fig. 47._]
FIRST STEPS.--Now lap together the inner surfaces of these boards (Y, Z), so the ends are toward you, as shown in Fig. 45. Then, after measuring the thickness of the boards to be joined (the thinnest, if they are of different thicknesses), set your compa.s.ses, or dividers, for 1/4 inch, providing the boards are 1/2 inch thick, and, commencing at the work edge of the board, step off and point, as at A, the whole width of the board, and with a square make the two cross marks (B), using the two first compa.s.s points (A), then skipping one, using the next two, and so on.
[Ill.u.s.tration: _Fig. 48._]
[Ill.u.s.tration: _Fig. 49._]
[Ill.u.s.tration: _Fig. 50._]
When this is done, turn up the board Z (Fig. 46), so that it is at right angles to the board Y, and so the outer surface of the board Z is flush with the end of the board X, and with a sharp knife point extend the lines B along with the grain of the wood on board Z, up to the cross mark C. This cross mark should have been previously made and is located as far from the end of the board Z as the thickness of the board Y.
We now have the marks for the outer surface of the board Z, and the end marks of board Y. For the purpose of getting the angles of the end of the board Z and the outer side of board Y, a cross line (D, Fig. 47) is drawn across the board X near the end, this line being as far from the end as the thickness of the board Z, and a vertical line (E) is drawn midway between the two first cross marks (A).
Now, with your compa.s.s, which, in the meantime, has not been changed, make a mark (F), and draw down the line (G), which will give you the working angle at which you may set the bevel gage. Then draw down an angle from each alternate cross line (A), and turn the bevel and draw down the lines (H). These lines should all be produced on the opposite side of the board, so as to a.s.sure accuracy, and to this end the edges of the board also should be scribed.
CUTTING OUT THE s.p.a.cES.--In cutting out the intervening s.p.a.ces, which should be done with a sharp chisel, care should be observed not to cut over the shoulder lines. To prevent mistakes you should put some distinctive mark on each part to be cut away. In this instance E, H show the parts to be removed, and in Fig. 48 two of the cutaway portions are indicated.
<script>