Part 10 (2/2)

Do not skin out and throw away the ear cartilage but leave it adhering to the skin of the inner side of the ear. Without it this skin is very frail and brittle and thorough pickling will prevent shrinkage and distortion of the ear.

Before leaving the head push it slightly towards the body on the wire and cut same close to end of nose. Pull head back to place, the wire disappears up the nose about 1/4 inch, then you can shape the nostrils and fill so they will not shrivel up in drying and look as though their owner had been a mouth breather.

[Ill.u.s.tration: OPOSSUM MOUNTED IN WALKING POSITION.]

If the general pose and appearance seem correct finish up by placing the feet and toes correctly. Nothing gives a mounted animal a more trampish, disreputable appearance than slouchy, run over feet with toes that don't seem to be on the job. Lastly comb the fur out and fluff it up before setting away to dry.

Animals up to the coyote in size are usually mounted by similar methods to the preceding. Sometimes a piece of board is subst.i.tuted for the body wire, especially in the larger specimens, the wires to which are too heavy to clinch readily. The skull is on a separate neck wire and all wires are fastened to the back board by pa.s.sing through holes and then stapling.

Of course it is possible to mount small specimens by the same methods most large ones are, by drawing the skin over a hard filling, in fact a statuette, which must be made to fit the skin. This method in the case of small animals requires so much time that it is impossible in ordinary commercial work.

Strive to put your mounted animals in easy natural poses unless you are making a grotesque, in which case go the length.

Clean the eyes and teeth with a brush when dry, and beat the fur to make it stand out. Fasten securely on whatever form of mounting you have decided on, countersinking the wires on the under side. Accessories, as a piece of food in the mouth or paws, are added now if they have been prepared for.

[Ill.u.s.tration: CAT SITTING AND WATCHING]

A slip with record of the specimen written on it and pasted to the under side of stand will usually be appreciated. If the mouth is wanted open it should be braced in that position, the lips, etc., held in place by clay. When it is dry this can be dug out with awls and modelling tools and the tongue, gums, and inside the mouth modelled in mache or some plaster composition. The tongue may be modelled in connection with the lower part of the mouth or made separately and fastened in place with a brad and some glue.

Colored wax, pink for the inside and black for the lips, applied hot with a little brush in several coats finish the open mouth. A little black wax will join the eyelids to the gla.s.s eyes if they have shrunk away and the inside of the nostrils should be coated with a little pink.

Bare skin on the end of the nose should be varnished.

CHAPTER XV.

MOUNTING LARGE ANIMALS ENTIRE.

Though at one time nearly all animals were mounted by the soft body or stuffing method as described in the previous chapter, very few of the larger ones are so treated now. An adequate frame is built in a body of the proper size and proportions, the surface of which reproduces those muscles lying next the skin. The skin, well pared down and poisoned, is sewed, pinned and glued to this surface.

In the small specimen clay was used next the skin in places to perfect the modelling, but such amounts would be required for a large animal as to affect the durability of the skin. Clay and plaster being in a dry state very absorbent, will eventually rob of all oily matter any skin in contact with them. Such skins will crack, split and finally disintegrate as thoroughly as those having an excess of fat adhering to them.

To prevent this a layer of some glue composition or paper is used just beneath the skin. As an example in this mode of mounting a black bear would answer nicely. If the leg bones are attached to the skin they may be unjointed at the toes and laid aside while the skin is well shaved down on its entire inner surface. A thoroughly flexible skin is entirely at the command of the taxidermist, one stiff or hard cannot be placed or kept in place at will.

After beaming, splitting the lips and nose cartilage, pocketing the ears and sewing up cuts and tears, the skin is dropped in the pickle. An outline sketch is made with chalk on the shop floor and on this the bones of the legs are arranged. A stiff wire bent along the back of each set of leg bones will guide us in bending the iron rods used as supports. These should be from 5/16 to 1/2 inch in diameter, threaded and fitted with two nuts at the lower end and eighteen inches or so longer than the leg bones themselves.

Of this extra length, enough is allowed below the feet to fasten to the pedestal, the balance is bent in a right angle from the end of the upper leg bone. At the distance of the hip joint from the central line of the body it is bent again parallel with the back board; for a hind leg. The front leg rods are bent in the same way at the joining of the shoulder blade with the humerus or upper bone of the front leg. You will readily see the desirability of preserving at least one set each of the hind and front leg bones. In such case the missing bones can be roughly blocked out of wood to the proper dimensions, while if none are saved you will have to do the same depending on the skin for measurements.

[Ill.u.s.tration: FRAME FOR BEAR MANIKIN.]

The end of the rods lying along the back should be bent again in a V shape to prevent their turning when fastened to it. The location of the hip and shoulder joints are marked on one side of the back board, the rods for that side laid in place and fastened by drilling holes each side of them and pa.s.sing loops of stout wire through and twisting them tightly on the other side with heavy pliers. The rods for the other side are fastened in the same manner, in fact they may be fastened with the same wires, but it will be stronger if the fastenings are separate. The leg bones are bound fast to the rods with wire or twine.

Holding the back board in the vise by the middle the leg rods with bone attached are adjusted to the position of the finished specimen. The threaded ends which project below the feet are bent straight down.

A rough pedestal of boards on 24 cleats at each end, is made, the frame placed on it and marking where the rods will enter, bore suitable holes to receive them. One nut is turned up each rod a short distance and after inserting in the holes in the pedestal the others are screwed up tightly from below.

<script>