Part 10 (1/2)

The guanaco pelt being of a woolly nature makes it unnecessary to run it all the same way and the entire skins are utilized in spite of their ungainly shape, the flaps and tabs trimmed off filling the indentations around the outer edge of the robe. They make an excellent camp blanket as light and warm as the malodorous, hairy rabbit skin robe of Hudsons Bay, and no Patagonian ranch house bed is complete without its guanaco coverlet.

You will likely be called on to repair robes much oftener than to make them and such work is nearly all profit, as it generally consists in sewing up rips and tears in the skins. Never attempt to do this from the front or fur side as it can only be done right from the back. To do this at least one side of the lining will have to be ripped and the robe turned, turning it back and resewing it on completion. Linings are turned under at the edges all around.

[Ill.u.s.tration: PATAGONIAN ROBE OF GUANACO SKINS.]

Worn and soiled linings and tr.i.m.m.i.n.g often need replacing with new material and it is sometimes necessary to purchase an unlined goat ”plate” to repair robes of that common variety. Worn robes can be cut down in size if no similar material is to be had for repairs.

CHAPTER XIV.

MOUNTING ENTIRE SMALL FUR ANIMALS.

In Chapters VI and VIII directions are given for skinning and preparing this cla.s.s of animals for mounting, so with the skin properly cleaned and poisoned before us the next thing is to cut the wires for a supporting frame. These are six in number usually, body wire, tail wire and one for each leg. The body wire is about one-half longer than from nose to base of tail; tail wire the length of the tail bone and half the body, and each leg wire twice the length of the leg.

I have spoken of using a muskrat for an initial attempt as it is of a convenient size to handle and the length of its fur will hide small defects in the anatomy. Most books of instruction select a squirrel for the beginner's victim. It is true it is not as difficult as a hairless Mexican terrier but it is apt to discourage the learner. An opossum will do very well or any long haired animal of about that size.

We will first reconstruct a hind leg and if it is a fresh specimen being mounted without a bath in the pickle we can have the opposite leg in the flesh to guide, as to proper proportions. The wire is pa.s.sed through the cut in the bottom of the foot and along the back of the leg bones where it is secured in about three places by tying with small cord. The end is left projecting three inches beyond the end of the upper leg bone.

[Ill.u.s.tration: HIND AND FRONT LEG OF MUSKRAT WRAPPED READY TO CLAY AND RETURN TO SKIN.]

The muscles and flesh are replaced by winding on tow with stout thread until the approximate size is reached, when the surface is given a thin coating of clay and the leg is drawn back into its skin. The fore legs are in the same manner built to the joint with the shoulder blade.

After sharpening the tail wire to a point it is wound with fine tow and thread and coated with clay until it duplicates the bone and flesh removed. This is slipped into the tail sheath with the unwound end projecting into the body and the slit along the lower side of tail sewed up.

After making a ring about the diameter of a .22 sh.e.l.l on one end of the body wire place it on your sketch where the hip joint was marked, letting the wire run lengthwise of the body. Another ring similar is made at the shoulder. These form the points of attachment for the legs.

[Ill.u.s.tration: WIRING FOR SMALL ANIMALS, FRONT LEG WIRES TWISTED TO BACK WIRE.]

The skull, cleaned of flesh and poisoned, should have the muscles replaced with tow and the whole coated with clay. Force a piece of cork into the opening at the back of the skull. Sharpen the end of body wire and force it through the cork and out one of the nostrils. The skull is pushed back along the wire until it reaches the proper distance from the shoulder ring, when all but an inch or so of the projecting wire is cut off.

Insert the skull through the body opening and work it up the neck into its place in the head skin, letting the end of wire go through the nostril of skin also. This will hold the nose in place. Adjust the eyes and ears also.

Now pa.s.s the ends of leg wire through the rings from their opposite sides. The tail wire is pa.s.sed through the rear ring and twisted around the body wire a few times. The ends of leg wires projecting through the ring cross, so twist them together a turn or two with pliers, next bring them down and under the body wire, twisting them together, first one side of it and then the other. This treatment will fasten the legs and tail also firmly to the body wire.

Thus we have the skin with head, tail and legs filled out and the supporting wires fastened together. The remainder of filling, usually chopped tow, is placed with fingers, forceps, and stuffers. First a good layer next the skin all around, then part this and fill in the center a little at a time, first at one end, then the other. Put a good cus.h.i.+on at the hips and shoulders between the wires and the skin and also at the back. Fill out the neck well but do not stretch it unduly.

Begin sewing up at both ends of the opening cut, drawing a few st.i.tches up and tying the thread while you fill a little more. Model the animal into shape from time to time by pressure with your hands and when filled out and sewed up tie the threads together.

Our animal is now lying on its back with head, tail and limbs extended; bend them into some natural position and set it on its feet. It may be well to force a little chopped tow and clay into the bottoms of the feet and draw the cuts in them together with a few st.i.tches around the leg wire projecting from them.

A temporary stand of a piece of board supported on cleats at each end is prepared and a number of holes bored for the leg wires. A little experimenting will find the proper place for these when the surplus ends of wire are bent along the bottom of the board and fastened with staples. Complete the head and face modeling now, filling out the cheeks and lips and pinning them in place. Work the skin around the eyes and ears into proper place and fasten with pins.

Fill eye sockets with sufficient clay and set the eyes, drawing the lids down where they belong.

Any deficiencies at the back of the head can be filled through the ears.

In the case of a muskrat the ears are so insignificant that they only need a little clay and tow forced into them to hold them in place. More prominent ears as those of fox, 'c.o.o.n, or wild cat must be filled with a pasteboard form, cut the proper size and shape, coated with liquid glue and inserted from the inside before returning the skull to the skin. The ears of all animals should be pocketed when skinned, that is turned inside out to their tips to admit preservatives and later some filling material which will retain their shape when dry.