v3 Chapter 421： Prepare (1/2)

Zhang Heng found a place without people, and after Feng Zi and Qiu Ming both found a hiding place, they later pulled out the [hidden sheath] around their waist.

This time, because he didn't get into a state of war as soon as he came up, Zhang Heng also had more time to prepare and adjust. He held the knife with both hands, slowly raised it over his head, and put out a starting gesture.

At the same time, Qiu Ming on the other side also opened his eyes wide and stared at him without blinking. He didn't want to miss the scene of Zhang Heng's sword as before.

However, despite Qiu Ming's full attention, in the end he failed to fully capture the movement of Zhang Heng's knife. His eyes barely saw an afterimage, and then he saw the hunting type Ⅵ robot control center. The location, sparks, and a cut of about 20cm long was cut from the metal shell.

Moreover, this knife is so powerful that it directly cuts through the heavy shell of the robot.

The attacked hunting and killing type VI robot switched to the defensive mode at the first time, and moved its left arm to aim at Zhang Heng. At the same time, the sickle on the two feet had been cut to Zhang Heng one step in advance.

一次 Zhang Heng didn't cut them with [Hanging Sheath] this time. He needs to ensure the completeness of this robot as much as possible in order to make it play the greatest power in the next battle.

Therefore Zhang Heng chose to increase his movement speed, avoiding the split of the two sickle feet by himself, and at the same time hurled the second knife before the heavy machine gun did not aim at him.

If it wasn't for his own eyes, Qiu Ming really couldn't believe that someone could practice the sword to such a degree.

Zhang Heng waved this knife's landing point in the high-speed movement and the first knife perfectly coincided with each other. It is not bad. The accuracy is like measuring with a ruler!

Qiu Ming even wondered if this was just a coincidence in probability, and as if to answer his question, Zhang Heng then cut out the third and fourth knife ... each knife was the perfect landing point, although A few knives are not as strong as the first knife that has been brewing for a long time, but they are also cutting through the metal shell of the robot a little bit along the previous trace.

And this time Qiu Ming saw it clearly enough, he found that the most difficult self-healing function of the hunting and killing type Ⅵ robot actually failed, and the metal near the wound cut off by Zhang Heng obviously changed, but for some reason It is impossible to let the wound heal.

Zhang Heng's knife fell on the metal shell of the robot like a storm, this time he completely cut through the metal shell with only five knives, while the hunting type VI robot on the other side had already folded his left hand. Heavy machine gun.

The main reason is that Zhang Heng is now completely in front of it, and the distance between the two sides is less than half a meter. At this distance, the judgment procedure for hunting and killing the Type VI robot will preferentially use the melee weapon, that is, the right-handed giant sword and the body below it. Eight legs attacked, but Zhang Heng did not continue to give it a chance.

At the sixth time, Zhang Heng penetrated the [hidden sheath] into the 20cm-long wound and cut off several main lines next to the control center. The hunting type VI robot seemed to be pressed by someone the next moment. Like the pause button, all actions suddenly froze in midair.

One of the sickle legs was less than an inch away from Zhang Heng's chest, but eventually he could no longer move forward.

Zhang Heng then cut off the chest of the hunting and killing type VI robot with [Hidden Sheath] and took out its signal receiver. After doing all this, Feng Zi and Qiu Ming walked out of the bunker again.

Zhang Heng said to Feng Zi, ”I'll re-encode the signal receiver, and leave it to you. You can help it replace the line that I cut off, but don't hurry up and wait until I put the signal receiver. Put it in and connect it, as well as the last tungsten steel welding. ”