Part 12 (2/2)

It is admittedly poor workmans.h.i.+p to use ill-fitting washers and poor taste to use bra.s.s washers on high grade gold screw balances, but the fact should not be overlooked that the manufacturers of many fine watches use washers to a limited extent, even when an abundance of balance screws are available and very fine Swiss models are often supplied with a pair of thin platinum washers which are not easily detected. The regulator should not be moved from the center of the index in correcting the mean time but should be used for minor final regulation only. The length of the hairspring should also not be disturbed in correcting the mean time of an adjusted watch and while a slow rate can be corrected by reducing the weight of a pair of balance screws it is necessary to use either heavier screws or washers for correcting a fast rate.

76. _Importance of Properly Fitted Regulator._

Final regulation of watches is necessary after making repairs regardless as to whether they have been adjusted to positions or not.

Position rating does not necessarily suggest that the timing has been completed as the object is only to limit the variations from one position to any other and a test of three or four days should always be made in one position after the position rating has been completed.

This additional timing has for its purpose the close regulation of the watch either in the pendant up position or in the position it is carried. The last column on the rate card is reserved for this purpose. In this respect the repairer who comes in contact with the customer may gain considerable advantage by noting in which pocket the watch is usually carried and then being guided in the final regulation by this knowledge. The method of doing this regulating consists generally of moving the regulator which requires certain attention to be effective when it is moved.

The regulator should be carefully fitted around the dome and all attachments in connection should be tightly fitted to the plate or bridge so that they will remain rigid when regulation takes place.

The tension around the dome should be even and if a tension spring is used in connection it should be strong enough to keep the regulator against the screw constantly without sticking at any point as the screw is moved forward and backward.

It should also be closely examined to see that there is no shake. This can be determined by lightly taking hold of the segment holding the regulator pins and moving it up and down and side ways before the tension spring is fitted. This should be examined with a gla.s.s and a correction made if any looseness is noted.

77. _Effect of the Middle Temperature Error._

In the final regulation of watches it is important that the middle temperature error receive due consideration. This error is always a few seconds fast as explained in temperature adjusting Chapter V, No.

21, and is of some consequence in the larger number of complaints regarding losing rates in the pocket, compared to complaints of gaining rates.

The position rating as well as the final regulation is generally done in normal temperature which produces a rate from two to four seconds faster than the heat extreme and it is to be expected that the pocket rate will be slower because the temperature will be higher than normal. This loss may not be the full amount of the middle error as it would depend upon the actual temperature encountered for the entire twenty-four hours and the watch may only be subjected to the pocket temperature for a part of this period. This works in exactly the same way in a lower temperature, as the variation is a loss in either direction from the middle or normal temperature and in case that the watch should be subjected to a freezing temperature at night the result will be a loss during that period.

As an example we will a.s.sume the regulation of a watch in which the temperature rate at the extremes of 40 and 90 Fahr. is perfect, while at the temperature of 70 it will time four seconds fast.

Now if this watch is regulated to no variation in the normal temperature it will be plainly seen that there will be a loss of four seconds per day if the watch is placed in service at either of the temperature extremes. If it had been regulated to run four seconds fast in the middle or normal temperature it would time more nearly correct in the pocket.

It is safe to a.s.sume that the watch will lose its proportional rate with a lesser change in temperature and for this reason it is of advantage to finally regulate all watches from two to four seconds fast in the rack rather than to time them just correct.

78. _Some Practical Reasons for Slow Rates._

There are additional reasons for the suggestion of timing watches a few seconds fast rather than just correct. Among them may be mentioned the fact that many watches are carried in the left vest pocket, and that in this instance they very often a.s.sume the pendant right position which is generally a trifle slow compared to pendant up in most watches of close adjustment. Magnetism to any extent whatever always causes a slow rate and this will have its effect whenever the balance, hairspring, regulator, regulator spring or pallet are slightly effected or when the mainspring, large winding wheels or case springs are considerably charged and experiments have shown that in no instance has a fast rate been produced from this cause.

The gradual weakening or loss of elastic force of the hairspring is also a factor to be considered.

There are some influences which cause a gaining rate that to some extent may offset these losses, although in the absence of necessity for cleaning or other repairs these influences are slight in comparison to the natural and possible causes for a slow rate.

PART III

SPECIAL NOTES

<script>